Position：Oil Pumps > Product > High viscosity oil pumps > LC Roots oil pump /LC high viscosity heavy oil pump series

LC Roots oil pump /LC high viscosity heavy oil pump series

Production Place：

Supplier：

EMAIL：kemaiind@outlook.com

LC Roots oil pump /LC high viscosity heavy oil pump seriesDetailed introduction

LC Roots pump /LC high viscosity heavy oil pump series overview

LCW high viscosity heavy oil pump, on the basis of LC pump, to solve the transmission of asphalt and condensate oil, in the pump shell surface or end cover with insulation layer, the use of steam or heat conduction oil circulation of heat preservation of the pump studio, so as to continuous and intermittent work of the pump, provide convenient and good conditions.

LC Roots pump is divided into belt drive and gear reducer drive in two forms.

This pump has the following characteristics: low revolution, high efficiency, small volume, large flow, small power consumption, strong self-priming ability, no oil diversion, easy to use and so on.

It can be widely used to transport petroleum and petroleum products (gasoline can be replaced by copper pump vane) and to transport all kinds of oil and liquid in factories.

Such as crude oil, paint, lubricating oil, glass glue, grease acid, toothpaste and light alkaline (soap processing) liquids;

Food processing can transport a variety of liquids, such as soy milk, yeast, sugar and so on.

Loading and unloading all kinds of tank cars and oil tankers, such as fast, high efficiency, easy to use, can be positive and reverse work.

LC Roots oil pump is composed of pump body, pump cover, shaft, gear, rotor, packing, gland and other components, the pump has two forms of belt drive and gear reducer drive, can reverse the effect, the two ends of the shaft is equipped with a framework oil resistant seal, the middle is equipped with oil return device, to prevent air intake or oil leakage.

Roots pump has the following characteristics:

1. Insensitive to dust and water vapor contained in the pumped gas;

2, the rotor does not need lubrication, no oil in the pump cavity;

3, the vibration is small, the rotor dynamic balance condition is good, no exhaust valve;

4, Driving power is small, mechanical friction loss is small;

5, compact structure, small footprint;

6. Low operation and maintenance cost.

7, in a wide range of pressure with a large pumping speed;

8, start fast, can work immediately;

Roots pump working principle:

In the pump cavity, there are two "8" shape of the rotor vertically installed on a pair of parallel axis, driven by a pair of gear ratio of 1 for each other reverse synchronous rotation movement.

There is a certain gap between the rotor and the inner wall of the rotor and the pump shell, so that high speed operation can be realized.

Because Roots pump is a vacuum pump without internal compression, usually the compression ratio is very low, so the high and middle vacuum pump needs the front pump.

The ultimate vacuum of Roots pump depends not only on the structure and manufacturing accuracy of the pump itself, but also on the ultimate vacuum of the pre-pump.

In order to improve the ultimate vacuum of the pump, the Roots pump can be used in series.

Installation of Roots oil pump /LC high viscosity heavy oil pump

LC Roots pump support or flange and its drive motor should use a common installation base, base.

Flanges or supports should have sufficient stiffness to reduce vibration and noise caused by the operation of the rotor pump.

The motor and the rotor pump shall be connected by elastic coupling, coaxiality less than 0.1 mm, inclination Angle shall not be greater than 1 degree.

When installing the coupling, hammer should not be used to avoid damaging the gears and other parts of the rotor pump.

When fastening the foundation screw of rotor pump and motor, the force of the screw should be uniform and the connection should be reliable.

When the coupling is rotated by hand, the rotor pump should be felt to rotate easily without any abnormal phenomena such as clamping, and then the pipe can be matched.

LC Roots pump oil suction pipe diameter should be large enough to avoid narrow channels or sharp turns.

Reduce elbows and remove unnecessary valves.

Accessories, as far as possible to reduce the pump installation height, shorten the length of the oil suction pipe, to reduce pressure loss.

Pipe joints and other components should be well sealed to prevent air intrusion, so as to control the occurrence of cavitation and cavitation.

Before starting operation, the shell of the rotor pump is filled with the liquid to be transported to facilitate safe start-up.

If the ambient temperature is lower than the freezing point, hot steam should be entered into the pump in advance to preheat the pump, and then the rotor pump can be started.

The direction of rotation of the rotor pump should be with the inlet.

The oil outlet is consistent. If the rotor pump runs for the first time, or is idle for a long time, it is best to run for an hour or so under the condition of no load or small load. If abnormal temperature rise is detected in advance in the running phase.

Leakage. Vibration and noise, should stop inspection,

The outlet pipe of LC Roots pump should also be equipped with a safety valve and other protective devices, so that once the outlet channel of the pump is blocked, the safety valve can be opened to relieve pressure.

For the need for positive and negative LC Roots pump, the import and export pipeline are required to set up the safety valve.

Roots pump /LC high viscosity heavy oil pump performance parameters table

型号

流量

m3/h

工作

压力

mpa

进出

口径

允许吸

上高度

传动形式

配用功率

功率

泵效率

选数

r/min

介质

温度

≤°C

重量

应用范围

减速器

型号

三角带

代号

电动机型号

LC-10/0.6

0.6

ZD14

A1778

Y	100L2-4
YB

3.0

400

140

167

柴油、

机油、

甘油、

石油、

牙膏、

食用油、稠油等、

LC-18/0.6

0.6

ZD14

A1778

I	Y	132S-4
	YB

5.5

400

140

II	Y	112M-4
	YB

4.0

140

219

LC-38/0.6

0.6

ZD14

B2350

II	Y	132M-4
	YB

7.5

400

140

269

LC-50/0.6

0.6

100

ZL200

Y	180M-4
YB

445

140

1160

LC-80/0.6

0.6

200

ZL200

Y	225M-4
YB

209

140140

LCQT-100/0.6

100

0.6

200

ZL23.1

Y	250M-4
YB

254

140

LCQT-10/0.6

0.6

ZD14

B2350

I	Y	100L2-4
	YB

3.0

400

140

167

气油、

容剂油、

煤油等、

LCQT-18/0.6

0.6

ZD14

A1778

II	Y	132S-4
	YB

5.5

400

140

219

Y	112M-4
YB

4.0

140

LCQT-38/0.6

0.6

ZD14

A1778

II	Y	132M-4
	YB

7.5

400

140

269

LCQT-50/0.6

0.6

100

ZL200

Y	180M-4
YB

18.5

445

140

1160

LCQT-80/0.6

0.6

200

ZL23.1

Y	180M-4
YB

209

140

LCQT-100/0.6

100

0.6

200

ZL23.1

Y	250M-4
YB

254

140

LCW-10/0.6

0.6

ZD14

A1778

Y	100L2-4-4
YB

3.0

400

140

167

沥青、

冷凝油、

稠油等、

LCW-18/0.6

0.6

ZD14

A1778

I	Y	132S-4
	YB

5.5

400

140

219

II	Y	112M-4
	YB

4.0

140

LCW-38/0.6

0.6

ZD14

B2350

Y	132M-4
YB

7.5

400

169

LCW-50/0.6

0.6

100

ZL200

Y	180M-4
YB

18.5

445

140

1160

LCW-80/0.60

0.6

200

ZL23.1

Y	225M-4
YB

209

140

LCW-100/0.6

100

0.6

200

ZL23.1

Y	250M-6
YB

254

140

For more informationcontent

上一篇：NYP high viscosity heavy oil pump 下一篇：What is a screw pump?

与LC Roots oil pump /LC high viscosity heavy oil pump seriesRelated Products

Screw high pressure diesel pump

Sscrew high pressure diesel pump referred to as screw diesel pump, model: 3G type, SN type, G type and other mainly used in electric power, chemical, petroleum and other fields.

Self-priming explosion-proof di

Self-priming explosion-proof diesel pump itself has explosion-proof and self-priming function, usually referred to as self-priming diesel pump; Model number: CYZ. The pump has the characteristics of simple structure, high efficiency, large f

CYB-T diesel pump

Diesel pump is mainly used for the transport of diesel oil, in which the centrifugal diesel pump pressure is normal pressure, but has better self-priming performance; CYB-T centrifugal diesel pump also has the characteristics of explosion-pr

Electric diesel pump(380V)

CYB-T diesel oil pump has the characteristics of large flow rate, high efficiency and explosion-proof, which belongs to self-priming oil pump. Electric diesel pump flow range: 3-800 cubic meters/hour, caliber from 1 inch, 2 inch, 3 inch, 4 i

网站首页 | 加入收藏 |

0317-8296807

kemaiind@outlook.com

联系方式

Address： Industrial Development Zone, Hebei Province
TEL：0317-8296807

FAX： 0317-8181816

HOME

Company profile

Dynamic

Product

information

Knowledge

Contact Us

LC Roots oil pump /LC high viscosity heavy oil pump series

LC Roots oil pump /LC high viscosity heavy oil pump seriesDetailed introduction

与LC Roots oil pump /LC high viscosity heavy oil pump seriesRelated Products

联系方式

PRODUCT CATEGORY

News

Support